Small inclinometer

KB-DB/KB-EB Inclinometer　±5° to ±10°CE

The KB-DB and KB-EB inclinometers are suitable for monitoring the conditions of structures being constructed or measuring the behavior of structures for a long period. The KB-DB is for measurement in one direction, while the KB-EB is for simultaneous measurement in both X and Y directions.

Protection ratings : IP 67 equivalent

KB-DB/KB-EB Inclinometer
Features
  • Made of all stainless steel with excellent corrosion resistance
  • Wall mounting and vertical installation
  • Waterproofness and excellent stability
  • Two (X and Y) directional simultaneous measurement with KB-EB

  • Specifications
    Type No. of measuring axis Capacity Rated output Non-linearity Temperature range
    KB-5DB 1 axis ±5°

    Approx. 1mV/V  (2000 x 10-6 strain)

    		 0.5%RO -20 to +60℃
    KB-10DB ±10°
    KB-5EB 2 axis ±5°
    KB-10EB ±10°

    Output polarity

    The measured value moves in the direction of the arrow on the label on the body of the unit in relation to the change in inclination.

More Information

Coating Materials

Coating materials

The type of coating required and the application method differ depending on the environment in which the strain gauge is to be used. In general, if one type of coating is not sufficient, multiple coatings can be combined to protect the strain gauges. At TML, the coating applied directly to the surface of the strain gauge is referred to sequentiallyas the first coating, with subsequent coating layers referred to sequentially as the second coating, third coating, etc. Multi-layer coatings are recommended for strain gauge protection.

img_multilayer-coating-01

SDS (Safety Data Sheet)

TML supplies SDS for all its strain gauge adhesives and coatings. Contact your TML supplier for more information.

Coatings in special substances

For use in special substances such as acids, alkalis and alcohols, contact TML or local representatives.

  • Type list
    Type Type of coating materials Operating temperature Curing conditions Materials Contents
    W-1 Hotmelt 0 to +50℃ Hot melting +100 to 120℃, hardening in room temperature Microcrystalline wax solid W-1Single 500g
    N-1 Rubber type solvent -30 to＋80 Air-drying, a half day in room temperature Special rubber based solvent thinned N-125ｇ
    K-1 Rubber type solvent -269 to +60℃ Air-drying, a half day in room temperature Special rubber based solvent thinned K-125g *
    UE-1 Rubber type solvent -40 to +150℃ Air-drying, a half day in room temperature Special rubber based solvent thinned UE-125g *
    SB tape Rubber type pressure sensitive -30 to +80℃ Pressure sensitive Butyl rubber SB-tape10mm (wide) × 3mm (thick) 5m long/roll
    VM tape Rubber type pressure sensitive -20 to +80℃ Pressure sensitive Butyl rubber VM-tape38mm (wide) × 0.635mm (thick) 6m long/roll
    KE-348W(White) Silicon -50 to +200℃ Air-drying solvent-thinned a half day in room temperature Silicon rubber KE-348100g
    KE-348T(Transparent)
    TSE3976-B Silicon -50 to +250℃ Air-drying solvent-thinned a half day in room temperature Silicon rubber TSE3976100g

    * This contents is for outside Japan. 

More Information

High-precision Tension Load Cell

 

High-precision Tension Load Cell

TLJ-NA Tension Load Cell　10kN～100kNCE

The TLJ-NA Tension Load Cell is designed considering JIS B 7728 "Load calibration devices for verifying material testing machine" and is the most suitable for verification of uni-axial tensile testing machine. Calibration in accordance with JIS B 7728 is available at extra cost.

Protection ratings : IP 65 equivalent

TLJ-NA Tension Load Cell
Features
  • High precision
  • Compatible with remote sensinginfo

  • Specifications
    Type Capacity Rated output Non-linearity Temperature
    range
    TLJ-10KNA 10kN 2mV/V
    (4000×10-6 strain) or over    		  0.03%RO -30 to +80 ℃
    TLJ-20KNA 20kN
    TLJ-50KNA 50kN
    TLJ-100KNA 100kN

    Output polarity

    Measurement moves in the plus direction with regard to increased tensile force.

More Information

Strain Transducer Optional Accessory

KMF Optional accessoryCE

Surface strain measurement onto steel and concrete structures is available with KM-100B or KM-100BT. (Optional fittings such as Spacer and Collar are available for fixing the model and positioning gauge length.)

o_km.jpg

Spacer KMF-12-100 / KMMF-22-100

A spacer is needed whenever strain transducer is installed to measure surface strain. The KMF-12-100 spacer is used to accurately locate the gauge length needed to attach KMF-22 and KMF-23B Collars to a structure.

KMF-12-100_87

KMF-12-100  Applicable transducer: KM-100B/KM-100BT

KMMF-12-100  Applicable transducer:KM-100M/KM-100HM/KM-100MT

Collar KMF-22-100 / KMF-23B-100 / KMMF-22-100 / KMMF-23-100

The KMF-22-100 Collars are used to mount a strain transducer to steel surface (2 per set), and KMF-23B-100 Collars are used to mount the transducer to the surface of concrete (2 per set).

For steel surfaces

KMF-22-100_88

For steel surfaces KMF-22-100  Applicable transducer : KM-100B/KM-100BT

KMF-22

For steel surfaces KMMF-22-100  Applicable transducer : KM-100M/KM-100HM/KM-100MT

KMMF-22

For concrete surface

KMF-23B-100_88

For concrete surface KMF-23B-100  Applicable transducer : KM-100B/KM-100BT

KMF-23B-100e

For concrete surface KMMF-23-100  Applicable transducer :KM-100M/KM-100HM/KM-100MT

KMMF-23

Protective Cover KMF-31-100/KMF-32B-100

The KMF-31-100 protective Cover is used to protect the transducer attached onto steel surface with a KMF-22 Collar, and the KMF-32B-100 is the same onto concrete surface with a KMF-23B Collar.

For steel surfaces : KMF-31-100
Applicable transducer : KM-100B/KM-100BT

KMF-31-100

o_km4

For concrete surface KMF-32B-100
Applicable transducer : KM-100B/KM-100BT/KM-100HB/KM-100M/KM-100HM/KM-100MT

KMF-32B-100

o_km5

Non-stress meter case KMF-51

The KMF-51 is used to measure the linear thermal expansion coefficient and dry shrinkage strain when case with a transducer inside is embedded in concrete.

Type Applicable transducer
KMF-51 KM-100B/KM-100BT
KM-100M/KM-100MT

KMF-51

o_km6

More Information

Standing-type Inclinometer

KB-AB/KB-AC Inclinometer　±1° to ±5°CE

The KB-AB and KB-AC are low-capacity inclinometers. They are used to monitor the conditions of inclination of neighboring structures built by urban civil engineering works. The KB-AB measures inclination in one direction, while the KB-AC measures inclination in both X and Y directions.

Protection ratings : IP 67 equivalent

KB-AB/KB-AC Inclinometer
Features
  • Made of all stainless steel with excellent corrosion resistance
  • Easy carriage and installtion with external stopper
  • Two (X and Y) directional measurement with KB-AC
  • Excellent stability

  • Specifications
    Type No. of measuring axis Capacity Rated output Non-linearity Temperature range
    KB-1AB 1 axis ±1° Approx. 1mV/V
     (2000 x 10-6 strain)    		 0.5%RO -20 to +60℃
    KB-2AB ±2°
    KB-5AB ±5°
    KB-1AC 2 axis ±1°
    KB-2AC ±2°
    KB-5AC ±5°

    Output polarity

    Measurement moves in the direction of the arrows on the label on the inclinometer with regard to change in inclination.

More Information