Compression Load Cell CLG-NB

CLG-NB Compression Load Cell 10kN to 200kNCE

The CLG-NB Load Cell is a high precision load cell in a thin, hermetically sealed package. It is widely used in tight spaces and as a system sensor for industrial machinery.

Protection ratings : IP 67 equivalent

Compression Load Cell CLG-NB
Features
  • Hermetically sealed, High precision, High stability
  • Low profile, Easy to install
  • Most applicable as system sensor for industrial machines

  • Specifications
    Type Capacity Rated output Non-linearity Temperature
    range
    CLG-10KNB 10kN 2mV/V
    (4000×10-6 strain) ±0.5 %    		 0.2 %RO -20 to +70 ℃
    CLG-20KNB 20kN
    CLG-50KNB 50kN
    CLG-100KNB 100kN
    CLG-200KNB 200kN

    Output polarity

    Measurement moves in the minus direction with regard to increased compressing force.

More Information

Dynamic Strainmeters Analog type Carrier type Dynamic Strainmeter DA-17A

Carrier type Dynamic Strainmeter DA-17A

The DA-17A is a carrier wave type dynamic strainmeter with frequency response of 2.5 kHz. One unit is for one measurement channel, and two or more units can be installed in an exclusive case or rack to make a multi-channel system. 
By installing the units in the exclusive carrying case for computer control, control from a PC via LAN is possible such as setting of sensitivity and low pass filter, operation of balancing and calibration, and acquisition of setting and monitor values.

Carrier type Dynamic Strainmeter DA-17A
Features
  • Frequency response of DC to 2.5 kHz
  • Digital monitor of output voltage, with indication of maximum / minimum value and open / over
  • Electronic automatic balancing
  • Isolation between input and output
  • Automatic tracking capacity balancing
  • Peak hold function privided
  • Dual output
  • Built-in low-pass filter
  • Insulation resistance check function for strain gauge bridge
  • External control possible for balancing and calibration signal output
  • Dual power supply of AC and DC
  • Possible control by PC (when installed in exclusive case)

  • Specifications
    Type DA-17A
    Measuring object Strain
    Number of channels 1 channel
    Measuring range

    ±50000 x 10-6 strain
    Frequency response DC to 2.5 kHz
    External dimensions 40(W) x 140(H) x 266(D) mm
    Weight Approx. 870 g
    Power supply AC 90 to 132 V 50 / 60 Hz 7.5 VA MAX. (AC100 V)
    DC 10 to 30 V 0.25 A MAX. (DC12 V)

More Information

Compression Load Cell CLU-NA

CLU-NA Compression Load Cell 10kN to 1MNCE

The CLU-NA Load Cell is an inert-gas encased load cell in a hermetically sealed package. The strain sensing element has a simple structure that enables highly precise and consistent measurements over long periods of time.

Two independent output type is aslo available on request.

Protection ratings : IP 65 equivalent

Compression Load Cell CLU-NA
Features
  • Long-term stable measurement
  • Easy handling

  • Specifications
    Type Capacity Rated output Non-linearity Temperature
    range
    CLU-10KNA 10kN 2mV/V
    (4000×10-6 strain) ±0.2 %    		 0.15 %RO -30 to +80 ℃
    CLU-20KNA 20kN
    CLU-50KNA 50kN
    CLU-100KNA 100kN
    CLU-200KNA 200kN
    CLU-500KNA 500kN
    CLU-1MNA 1MN

    Output polarity

    Measurement moves in the minus direction with regard to increased compressing force.

More Information

Compression Load Cell CLP-NB

CLP-NB Compression Load Cell
 10kN to 10MN CE

CLP-NBThe CLP-NB is a general purpose compression load cell having a column shape strain sensing element. A variety of capacities ranging from 10 kN to 10 MN is available.

Dual output type having two independent inputs and outputs is also available on request.

Protection ratings : IP 65 equivalent

圧縮型荷重計 CLP-NB
Features
  • Load cell having appropriate capacity can be chosen among various types
  • Easy to handle
  • CE marking compliant

  • Specifications
    Type Capacity Rated output Non-linearity Temperature
    range
    CLP-10KNB 10kN 1.5mV/V
    (3000×10-6 strain) ±0.2 %    		 0.1% RO -20 to +70 ℃
    CLP-20KNB 20kN
    CLP-30KNB 30kN
    CLP-50KNB 50kN
    CLP-100KNB 100kN
    CLP-200KNB 200kN
    CLP-300KNB 300kN
    CLP-500KNB 500kN
    CLP-1MNB 1MN
    CLP-2MNB 2MN
    CLP-3MNB 3MN
    CLP-5MNB 5MN 0.2％ RO
    CLP-10MNB 10MN

    Output polarity

    Measurement moves in the minus direction with regard to increased compressing force.

More Information

Dynamic Strainmeters Digital type Handheld Dynamic Strainmeter DH-14A

Handheld Dynamic Strainmeter DH-14A

The DH-14A is a handheld and battery-operated dynamic strainmeter having 4 measurement channels. Dynamic strain is easily measured while monitoring numerical values and wave forms. Trigger measurement mode and free-run measurement mode are available. The DH-14A is well suited not only for measurement in fieldwork or on moving object, but also for checking sensors and input noise as a checker. Using 4 AA alkaline batteries commercially available, the meter allows measurement for 4 consecutive hours (or for 6 hours in power saving mode).

Handheld Dynamic Strainmeter DH-14A
Features
  • Simultaneous sampling of 4 channels
  • Measured data indicated by waveform
  • ECO mode (power saving mode) equipped
  • Powered by 4 AA alkaline batteries
  • Measured data conforms to DADiSP format
  • TEDS compatible

  • Specifications
    Type DH-14A
    Measuring object Strain
    DC voltage (with optional CR-4110, CR-4120)
    Thermocouple (with optional TA-01KT)
    Number of channels 4 channels
    Measuring range ±20,000 x 10-6 strain (at 2 V excitation) 
    ±80,000 x 10-6 strain (at 0.5 V excitation)
    Frequency response DC to 1 kHz (-3dB±1dB)
    Applicable gauge resistance 120 Ω, 350 Ω (Full bridge)
    Maximum sampling speed 50μsec (1-channel mode), 100μs (2-channel mode), 200μs (4-channel mode)
    External dimensions 150(W) x 63(H) x 150(D) mm (except projecting parts)
    Weight Approx. 1 kg
    Power supply 4 AA-size (LR6) alkaline batteries 
    AC adaptor (optional)

More Information

Dynamic Strainmeters Digital type PC control Dynamic Strainmeter DC-004P

PC control Dynamic Strainmeter DC-004P

The DC-004P is a PC control type dynamic strainmeter. It stores measured data in a PC which is connected via USB interface, without having a recording medium in the strainmeter. Since a continuous recording is possible, this strainmeter is most suited to measurement such as material testing.

PC control Dynamic Strainmeter DC-004P
Features
  • Manual trigger, data trigger and Interval trigger can be executed at the same time
  • 50 kHz sampling (at the fastest in 1-channel mode)
  • Simultaneous sampling of 12.5 kHz for 4 channels (4-channel type)
  • Capable of measuring a large strain of up to 80000×10-6 strain (with 0.5 V excitation)
  • Direct recording on a PC
  • Supporting long term measurement
  • 4-channel type and 2-channel type are supportable
  • Measured data conforms to DADiSP format
  • TEDS compatible
  • Control software (DC-7004P) supplied as a standard accessory

  • Specifications
    Type DC-004P
    Measuring object Strain
    DC voltage (with optional CR-4110, CR-4120) 
    Thermocouple (with optional TA-01KT)
    Number of channels 4 channels (4-channel type), 2 channels (2-channel type)
    Measuring range ±20,000 x 10-6 strain (at 2 V excitation) 
    ±80,000 x 10-6 strain (at 0.5V excitation)
    Frequency response DC to 2 kHz
    Applicable gauge resistance 120 Ω, 350 Ω (Full bridge)
    Maximum sampling speed 20μsec. (1-channel mode), 40μsec. (2-channel mode), 80μsec. (4-chaanel mode)
    External dimensions 120(W) x 50(H) x 180(D) (except projecting parts)
    Weight DC-004P : 4 channels type Approx. 600g
    DC-004P (-2) : 2 channels type Approx. 500g
    Power supply DC 10 to 16 V 0.3 A Max. (when supplied from DC jack)
    *Can be supplied from USB buspower

More Information

Compression Load Cell CLA-NA

CLA-NA Compression Load Cell 500N to 20kNCE

The CLA-NA Load Cell has a diaphragm type strain sensing element. It is compact, easy to operate and can be used to take consistent measurement.

Protection ratings : IP 67 equivalent

CLA-NA Compression Load Cell
Features
  • Splash-proof structure, Stable measurement
  • Small, Easy handling

  • Specifications
    Type Capacity Rated output Non-linearity Temperature
    range
    CLA-500NA 500N 1.5mV/V
     (3000×10-6 strain) ±0.5 %    		 0.2 ％RO -20 to +70 ℃
    CLA-1KNA 1kN
    CLA-2KNA 2kN
    CLA-5KNA 5kN
    CLA-10KNA 10kN
    CLA-20KNA 20kN

    Output polarity

    Measurement moves in the minus direction with regard to increased compressing force.

More Information

Cavity type Pressure Transducers PW-PA

PW-PA Pressure Transducer 100kPa to 50MPaCE

The PW-PA pressure transducer can make stable high-accuracy measurement over a long period of time. It is widely used in production lines and plants and to measure liquid pressure, air pressure, and so forth in laboratories.

Protection ratings
　IP 42 equivalent for PW-100KPA/PW-200KPA　/　 IP 65 equivalent for PW-500KPA ~ PW-50MPA

PW-PA Pressure Transducer
Features
  • Excellent stability and high precision
  • Easy handling

  • Specifications
    Type Capacity Rated output Non-linearity Temperature range
    PW-100KPA 100kPa 1 mV/V (2000x10-6 strain)±1 % 0.3 %RO -20 to +70 ℃
    PW-200KPA 200kPa 1.5 mV/V (3000x10-6 strain)±1 %
    PW-500KPA 500kPa 0.2 %RO
    PW-1MPA 1MPa
    PW-2MPA 2MPa 2 mV/V (4000x10-6  strain)±1 %
    PW-5MPA 5MPa
    PW-10MPA 10MPa
    PW-20MPA 20MPa
    PW-30MPA 30MPa
    PW-50MPA 50MPa

    Output polarity

    Measurement moves in the plus direction with regard to an increase in pressure.

More Information